Tile Calculator

Find out how many tiles and boxes to buy for a floor or wall. Add every room or section, choose your tile size, grout joint and layout, and get the boxes to buy, what is left over and the cost. Every step is shown.

Units

Example values shown. Replace them with yours.

Areas to tile

Add each room or section separately. Split L-shaped rooms into rectangles.

Area 1
Shape
Areas you will not tile

Kitchen islands, built-in cabinets, a bathtub footprint, etc.

Your tile
Grout joint width

Rectified porcelain often uses 1/16 in; most other tile 1/8 in or wider.

Layout pattern

Extra for cuts, breakage and future repairs.

How it is sold

Printed on the carton label.

Price (optional)
Tile price is quoted

Before you buy

  • Buy every box from the same production lot (shade and caliber are printed on the carton). Colors can vary between lots.
  • Keep at least one spare box after the job. Replacing a cracked tile years later is much easier with matching stock.
  • Coverage per box differs between products. Use the figure printed on the carton you are buying.
  • Add a price (per sq ft, per box or per tile) to see the tile cost.

How to use the tile calculator

  1. Measure the length and width of each area. Type feet and inches straight off the tape, or use the small unit menu in each box to switch to feet, yards, inches, or metric units. Split L-shaped rooms into rectangles and add each one as a separate area.
  2. If part of the floor will not be tiled, such as a kitchen island or a tub, enter that area under Areas you will not tile.
  3. Pick your tile size and grout joint. If your tile is not listed, choose Custom size and enter the length and width.
  4. Choose the layout. It sets a sensible waste allowance, which you can change.
  5. Choose how the tile is sold. Most US tile is sold by the box, with the coverage in square feet printed on the carton.
  6. Optionally add the price, quoted per square foot, per box or per tile, whichever is on the shelf tag. The cost is calculated on the boxes you actually buy, not just the area.

The formula

Area           = length × width            (sum of all areas − deductions)
Tile footprint = (tile L + joint) × (tile W + joint)
Tiles          = Area ÷ tile footprint
Tiles to buy   = round up( Tiles × (1 + waste %) )
Boxes          = round up( Area × (1 + waste %) ÷ coverage per box )

The calculator divides the area by the space one tile really occupies, which is the tile plus half a grout joint on every side. Many calculators skip the joint. That overstates the tile count slightly for small tile with wide joints.

Boxes are worked out from the coverage printed on the box, because that is what you buy. Partial boxes are always rounded up, and the leftover is shown so you know how much spare you will have.

Worked examples

Kitchen floor: 12 × 10 ft with 12 × 24 in porcelain

  1. Area: 12 ft × 10 ft = 120 sq ft.
  2. Tile footprint with a 1/8 in joint: 24.125 × 12.125 in = 2.03 sq ft.
  3. Tiles: 120 ÷ 2.03 = 59.1, so 60 tiles without waste.
  4. Add 10% for a straight layout: 59.1 × 1.10 = 65.0, so 65 tiles.
  5. Boxes at 15.5 sq ft each: 132 sq ft ÷ 15.5 = 8.5, so 9 boxes (139.5 sq ft).

Buy 9 boxes. You will have about 19.5 sq ft left for repairs.

L-shaped room on the diagonal with 18 × 18 in tile

  1. Split the room: 14 × 10 ft (140 sq ft) + 6 × 5 ft (30 sq ft) = 170 sq ft.
  2. Tile footprint with a 3/16 in joint: 18.1875² in = 2.30 sq ft.
  3. Tiles: 170 ÷ 2.30 = 74.0, so 75 tiles without waste.
  4. Diagonal layout, 15% waste: 74.0 × 1.15 = 85.1, so 86 tiles.
  5. Sold 5 per box: 86 ÷ 5 = 17.2, so 18 boxes (90 tiles).

Buy 18 boxes of 5 tiles.

How much extra tile to buy

Waste covers cuts at walls, breakage, tiles you reject for chips or color, and a few spares for future repairs. Use these as starting points, and go higher for small rooms with many cuts:

LayoutTypical wasteWhy
Straight / grid10%Cuts only at the edges
Offset / brick10%Similar cuts; long tile may need a 1/3 offset
Diagonal15%Triangular cuts along every wall
Herringbone / chevron20%Angled cuts on every edge, pattern alignment
Small room, many cuts15%Toilet, vanity, door jambs, closets

Large-format tile (24 in and up) in small rooms often needs 15% even when laid straight.

Assumptions and limits

  • Areas are flat and measured to the walls. Tile under cabinets or appliances is up to you; include it if the floor goes underneath.
  • The tile footprint includes the grout joint, which is why the tile count is a little lower than area ÷ tile size.
  • Boxes are calculated from the coverage on the box, including waste. Manufacturers measure coverage by the nominal tile size.
  • Waste percentages are industry rules of thumb, not guarantees. Complex layouts and inexperienced installers use more.
  • Prices you enter are applied to the full boxes you buy. Thinset, grout, trim, underlayment and labor are not included.

Common mistakes to avoid

Mixing inches and feet

Room sizes go in feet and inches; tile sizes go in inches. Typing 144 in the feet box for a 12 ft room makes the area 144 times too large. The separate ft and in boxes are there to prevent this.

Buying exactly the area

Without waste you will run out at the last row, and the next batch may not match. Different production lots can vary in shade.

Forgetting closets and doorways

Tile usually runs into closets and stops under the door, at the center of the threshold. Measure those small areas and add them.

Ignoring box rounding

Stores sell whole boxes. Comparing prices per square foot without rounding up to boxes can hide a big cost difference between two tiles.

Frequently asked questions

How many tiles are in a square foot?

Divide 144 by the tile area in square inches, including the joint. A 12 × 12 in tile with a 1/8 in joint covers about 1.02 sq ft, so about 1 tile per sq ft. A 12 × 24 in tile covers about 2 sq ft, and 3 × 6 in subway tile about 7.5 per sq ft.

How much extra tile should I buy?

Usually 10% for straight layouts, 15% for diagonal layouts or small rooms with many cuts, and 20% for herringbone. Keep at least one spare box after the job for future repairs.

Should I subtract the area of a toilet or vanity?

Usually no. Tile normally goes under toilets, and the cuts around them use tile anyway. Subtract only large fixed items the tile will stop at, such as kitchen islands, built-in cabinets or a tub.

How do I measure an irregular room?

Split it into rectangles and triangles, measure each and add them as separate areas. The square footage guide walks through common shapes.

Does this include grout and thinset?

No. Tile only. Use the grout calculator (the link in your results fills in your tile size). For thinset, follow the coverage chart on the bag for your trowel size.

How do I calculate tile by the square foot?

Multiply length × width in feet for each area to get square feet, add them up, and subtract anything you will not tile. The calculator shows the area to tile, the tiles per square foot for your size and joint, and the boxes, which are usually sold by the square foot.

Does this work for vinyl tile (LVT)?

Yes. Enter the vinyl tile size and set the joint to the smallest option, since most vinyl tile is butted with no grout. Use the coverage per box from the carton. For vinyl plank, the flooring calculator also estimates underlayment and trim.

Can I use this for wall tile?

Yes. Enter each wall as length × height and subtract windows and doors. For showers and tub surrounds, use the shower tile calculator, which handles niches and curbs.

Formulas covered by automated tests · Last reviewed · How we calculate