Grout Calculator

Find how many pounds and bags of grout you need from the tiled area, tile size, tile thickness and joint width. Also see how joint width changes the amount, and whether your grout type suits your joints.

Units

Example values shown. Replace them with yours.

Tiled area

Use the area from the tile calculator if you have it.

Tile & joint

Most ceramic and porcelain tile is 1/4–3/8 in thick. Check the box.

Grout joint width
Grout product
How to estimate

If your grout bag or data sheet gives coverage for your tile size and joint, use the product chart. It is the most accurate.

Grout type
Package size

About 100 lb/cu ft (1.6 kg/L) is the value common grout calculators use for cement grout. Replace it with your product's figure if you have one.

Before you buy

  • This is an estimate from joint geometry and an assumed grout weight per volume. Manufacturers publish coverage charts for each grout; if yours differs, trust the chart.
  • Mix only what you can use in about 30 minutes. Mixing in small batches also reduces waste.
  • Buy all grout from the same batch. Color can shift slightly between production runs.
  • Epoxy and premixed (urethane) grouts are often sold by volume, such as quart or gallon pails. Use the coverage chart on the pail for those.

How to use the grout calculator

  1. Enter the area you are grouting. If you used the tile calculator, its "Estimate grout" link fills this in for you.
  2. Choose the tile size and enter the tile thickness. Grout fills the full depth of the joint, so thickness matters as much as joint width.
  3. Select the joint width you will use, usually set by your tile spacers.
  4. Choose how to estimate. From the product chart uses the coverage printed on your grout bag for your tile and joint, and is the most accurate. From joint size estimates the weight from the joint volume and an editable grout weight per volume.
  5. Choose the grout type and package size. The results show the packages to buy and, for the estimate, the pounds and how far one package goes.

The formula

Grout share   = 1 − (L × W) ÷ ((L + j) × (W + j))
Joint volume  = area × grout share × tile thickness
Grout (lb)    = joint volume × density            (≈ 100 lb/cu ft cement grout)
Packages      = round up( grout × (1 + extra %) ÷ package weight )

Each tile and its joint form a repeating cell. The grout share is the part of that cell that is not tile. Multiply the share by the area and the joint depth (the tile thickness) to get the volume of the joints.

The calculator uses a density of about 100 lb per cubic foot of filled joint (≈ 1.6 kg/L) for cement grout and slightly more for epoxy. This is the design value most manufacturer charts use. Results usually land within 10% of manufacturer coverage charts. If your grout's chart differs, follow the chart.

Worked examples

100 sq ft of 12 × 12 in tile, 3/8 in thick, 1/8 in joints

  1. Grout share: 1 − 144 ÷ 12.125² = 2.05% of the surface.
  2. Volume: 100 sq ft × 2.05% × 3/8 in = 0.064 cu ft.
  3. Weight: 0.064 × 100 = 6.4 lb, + 10% = 7.05 lb.

One 25 lb bag is plenty. At this size it covers about 390 sq ft.

50 sq ft of 2 × 2 in mosaic, 1/4 in thick, 1/8 in joints

  1. Grout share: 1 − 4 ÷ 2.125² = 11.4% of the surface, more than five times the share for 12 × 12 tile.
  2. Volume: 50 × 11.4% × 1/4 in = 0.119 cu ft, which is 11.9 lb.
  3. + 10% = 13.1 lb.

Buy two 10 lb bags. Mosaics use a lot of grout.

Sanded, unsanded or epoxy?

GroutJoint widthGood for
UnsandedUp to 1/8 inNarrow joints, polished stone and glass that sand could scratch
Sanded1/8 in and widerMost floor tile; stronger, less shrinkage in wide joints
Epoxy1/16 in to 1/2 in (check product)Showers, kitchens, stain resistance; harder to install

Always confirm with the product data sheet. Some modern grouts are rated for a wide range of joint widths.

Assumptions and limits

  • Joints are filled to the full tile thickness. If your joints will be shallower, enter the actual grout depth as the thickness.
  • Tiles are rectangular and laid in a grid or offset pattern. Hexagon and other shapes have somewhat more joint per square foot.
  • Density is a typical value, not product-specific. Lightweight and premixed grouts differ.
  • Extra covers mixing loss, cleanup and grout left in the bucket.

Common mistakes to avoid

Forgetting tile thickness

A 1/2 in thick tile needs about a third more grout than a 3/8 in tile with the same joint, because the joints are deeper.

Using a coverage figure from a different tile

"One bag covers 100 sq ft" can be true for one tile and badly wrong for another. Coverage depends almost entirely on tile size and joint width.

Mixing the whole bag at once

Cement grout starts to set in about 30 minutes. Mixing too much at once is the most common source of wasted grout.

Frequently asked questions

How much grout do I need for 100 square feet?

It depends on the tile. 12 × 12 in tile with 1/8 in joints needs about 7 lb. 3 × 6 in subway tile needs about 17 lb. 2 × 2 in mosaic (1/4 in thick) needs about 26 lb. Enter your tile above for an exact estimate.

How many square feet does a 25 lb bag of grout cover?

From under 100 sq ft for mosaics with wide joints to over 1,000 sq ft for large rectified tile with 1/16 in joints. The results show "One package covers" for your exact tile.

Why does small tile need so much more grout?

Smaller tiles mean more joints per square foot. A 2 × 2 in mosaic has six times as many joints per foot as a 12 × 12 in tile.

Should I buy extra grout?

Yes, about 10%. Buy all bags from the same batch for consistent color, and keep a little sealed for future repairs.

Does this work for epoxy grout?

Yes. Select epoxy grout and the calculator uses a slightly higher density. Epoxy is usually sold in kits by volume, so check the kit coverage for your tile size as well.

Formulas covered by automated tests · Last reviewed · How we calculate