Shower Tile Calculator

Estimate the tile for a walk-in shower or tub surround in one place: wall tile, floor mosaic, the curb, niches and a bench. You also get cement board sheets and grout. Built for real bathroom remodels.

Units

Example values shown. Replace them with yours.

Shower size
Tiled walls

A standard tub or shower alcove is 5 ft (60 in). Also used for the floor.

Front to back. Also used for the shower floor.

From the floor, or the top of the tub, to where the tile stops. Tub surrounds are often 5–6 ft.

A window, or a glass panel fixed to the wall. Do not subtract the valve or niche.

Curb, niche & bench

2×4 stud walls give about 3.5 in.

Wall tile
Grout joint width

Rectified porcelain often uses 1/16 in; most other tile 1/8 in or wider.

Used for the grout estimate.

Layout pattern

Extra for cuts, breakage and future repairs.

How it is sold

Printed on the carton label.

Floor tile

Small mosaic tile is standard on shower floors because it follows the slope to the drain and gives better grip.

Grout joint width

Rectified porcelain often uses 1/16 in; most other tile 1/8 in or wider.

Used for the grout estimate.

Layout pattern

Extra for cuts, breakage and future repairs.

How it is sold

A 12 × 12 in sheet covers about 1 sq ft.

Prices (optional)
Wall tile price is quoted
Floor tile price is quoted

Before you buy

  • Waterproof every wall and the floor before tiling. Use a sheet or liquid membrane and follow its coverage chart. Waterproofing is the most important part of a shower.
  • Shower walls use 15% waste by default. Niches, curbs, valve cut-outs and outside corners mean more cuts than a floor.
  • Plan bullnose or metal edge trim for exposed tile edges, such as curb edges and the outer edge of a tile wall.
  • Buy all tile from the same lot, and keep a spare box for future repairs.

How to use the shower tile calculator

  1. Choose which walls are tiled: three walls for an alcove or tub surround, two for a corner shower, one back wall, or Custom walls to enter each wall's width and tile height yourself.
  2. Enter the back wall width, the side wall depth and how high the tile goes. Measure tile height from the floor, or from the top of the tub for a surround.
  3. Subtract any untiled area on the walls, such as a window. Then tick the extras you have: a curb, one or more recessed niches, or a built-in bench, and enter their sizes.
  4. Set up the wall tile and the floor tile separately. They are almost always different products.
  5. Optionally add prices to see a material cost for tile and backer board.

The formula

Walls       = (back width + 2 × side depth) × tile height        (alcove)
Niche       = + 2 × niche depth × (niche width + niche height)   (returns only)
Curb        = curb length × (2 × curb height + curb top width)
Bench       = + seat + front − wall hidden behind the bench
Floor       = back width × side depth
Wall tile   = (walls + niche + curb + bench) → tiles & boxes incl. waste
Backer      = round up( wall area × 1.10 ÷ 15 sq ft )          (3 × 5 ft sheets)

A common mistake is to subtract a niche. The back of a niche replaces wall tile one for one, but its four sides (the returns) are extra surface you must tile. The calculator adds the returns.

A curb has two faces and a top. Floor and wall tile are calculated separately, each with its own size, joint and packaging, because shower floors almost always use small mosaic sheets.

Worked examples

60 × 36 in walk-in shower, tiled to 8 ft, with niche and curb

  1. Walls: (5 ft + 2 × 3 ft) × 8 ft = 88 sq ft.
  2. Niche 12 × 24 × 3.5 in: returns add 2 × 3.5 × (12 + 24) = 252 sq in = 1.75 sq ft.
  3. Curb 5 ft long, 4.5 in tall, 4.5 in top: 5 × (9 + 4.5) ÷ 12 = 5.63 sq ft.
  4. Wall tile area: 88 + 1.75 + 5.63 = 95.4 sq ft. With 12 × 24 in tile and 15% waste, that is 54 tiles, or 8 boxes of 15.5 sq ft.
  5. Floor: 5 × 3 ft = 15 sq ft of 2 × 2 in mosaic + 15% = 17.25, so 18 sheets.
  6. Cement board: 89.75 sq ft × 1.10 ÷ 15 = 6.6, so 7 sheets.

Buy 8 boxes of wall tile, 18 mosaic sheets and 7 sheets of cement board.

Standard tub surround, 5 ft high, with 3 × 6 in subway tile

  1. Tub alcove: back wall 5 ft, end walls 2 ft 6 in each, tiled 5 ft above the tub.
  2. Walls: (5 + 2 × 2.5) × 5 = 50 sq ft. No floor or curb.
  3. Subway tile with 1/16 in joints: 388 tiles, + 15% = 446 tiles.
  4. Boxes of 10 sq ft: 57.5 ÷ 10 = 5.75, so 6 boxes.

Buy 6 boxes of subway tile.

Assumptions and limits

  • Walls are treated as flat rectangles. The tub or shower pan is not counted as tiled wall.
  • Niches use wall tile for all faces. The back panel replaces wall tile, so only the returns are added.
  • The curb is tiled on both faces and the top, using wall tile. Curb ends are small and covered by the waste allowance.
  • The bench is a box built against the back wall: its seat and front are added and the wall behind it is subtracted.
  • Cement board covers the tiled walls only. Shower floors are usually a mortar bed or foam pan, and curbs are often pre-formed.
  • Grout is estimated for cement grout with 10% extra, using each tile's size, joint and thickness.

Common mistakes to avoid

Using the wall tile on the floor

Large tile is hard to slope toward a center drain and can be slippery when wet. Most shower floors use 2 × 2 in mosaic, or larger tile with a linear drain.

Forgetting the curb and niche returns

These add only a few square feet, but they need the most cuts, and often edge trim. Running short on these pieces is common.

Measuring tile height to the ceiling when you will stop short

Decide where the tile stops: at the ceiling, at the showerhead plus about 6 in, or above the tub. Then measure that height. On an 8 ft alcove, every foot of height is about 11 sq ft of tile.

Skipping waterproofing

Grout and tile are not waterproof. Every shower needs a membrane on the walls, floor and curb. The results show the area to cover.

Frequently asked questions

How much tile do I need for a standard 60 × 32 in shower?

For three walls tiled to 8 ft: (5 + 2 × 2.67) × 8 ≈ 83 sq ft of wall, plus a 13.3 sq ft floor. With 15% waste, plan for about 95 sq ft of wall tile and about 16 mosaic sheets, before the curb and niche. Enter your exact sizes above for box counts.

How much extra tile should I buy for a shower?

15% is a sensible default for shower walls and floors, because niches, valve cut-outs, corners and the curb all need cuts. Use 20% for herringbone or diagonal layouts.

Should the shower tile go to the ceiling?

It is a design choice. Tiling to the ceiling looks finished and protects the wall from steam. Many showers stop 6–12 in above the showerhead. Enter whichever height you choose.

What size should a shower niche be?

Common niches are 12 in wide (between studs at 16 in on center) and 12–24 in tall, about 3.5 in deep in a 2×4 wall. Size the niche to whole tiles where you can, so cuts land outside the niche.

How many sheets of cement board do I need for a shower?

Divide the tiled wall area by 15 sq ft (a 3 × 5 ft sheet) and add about 10%. The calculator does this for you. A typical alcove tiled to 8 ft needs 6–7 sheets.

Do I need different grout for the shower floor?

Not necessarily, but floor mosaics have many joints and use far more grout per square foot than large wall tile. Many installers choose epoxy or high-performance grout in showers because it resists stains. The grout calculator compares joint widths.

Formulas covered by automated tests · Last reviewed · How we calculate