Drywall Calculator

Calculate how many sheets of drywall you need for walls and ceilings, minus doors and windows. You also get the joint compound, tape and screws to hang and finish them.

Units

Example values shown. Replace them with yours.

Rooms

Add whole rooms, or single walls and ceilings when you are only doing part of a room.

Surface 1
What are you covering?

For a wall: its width along the floor.

Drywall sheets
Sheet size

Longer sheets mean fewer seams to tape. 4 × 12 ft is common for walls taller than 8 ft and for ceilings.

10% for simple rooms. 15% or more for many corners, soffits or angled ceilings.

Joint compound (mud)

Ready-mixed all-purpose compound for taping plus two finish coats (a standard Level 4 finish).

USG literature gives about 9.4 gal; Fine Homebuilding about 11 gal for three coats. A smooth Level 5 finish uses more.

Container size
Cost: materials and installation (optional)

Enter your own prices and quotes. We do not show market prices. Labor is optional and kept separate.

Contractors often quote per square foot of board. Use your local quote.

Opening sizes

Pros often do not subtract small openings, because the cut-out pieces are rarely reusable.

A standard 3 × 7 ft door is 21 sq ft.

A 3 × 5 ft window is 15 sq ft.

Before you buy

  • Use moisture-resistant board in bathrooms and laundry rooms. Use cement board behind tile in showers.
  • Ceilings often use 5/8 in board, or 1/2 in sag-resistant ceiling board, when framing is 24 in on center. Check local code for garages next to living space, which often need 5/8 in Type X.
  • Outside corners need corner bead. Measure the total length of outside corners separately.
  • Compound and tape figures are typical for a standard three-coat finish (Level 4). A smooth Level 5 finish uses noticeably more compound.

How to use the drywall calculator

  1. Add each whole room with its length, width and wall height, and tick the ceiling if it will be drywalled too. Doing part of a room? Choose A single wall or A ceiling only instead.
  2. Enter the number of doors and windows in each room. Standard sizes are assumed and can be changed under Opening sizes.
  3. Choose the sheet size. Longer sheets mean fewer joints to tape.
  4. Adjust the waste allowance if the room has many corners, soffits or angles.
  5. Open Joint compound (mud) to change the coverage rate or container size, and Cost to add your prices and, optionally, a labor quote per square foot for hanging and finishing.

The formula

Wall area  = 2 × (length + width) × height
Ceiling    = length × width
Net area   = walls − doors − windows + ceilings
Sheets     = round up( net area × (1 + waste %) ÷ sheet area )
Screws     ≈ 1 per sq ft (walls), 1.25 per sq ft (ceilings)
Compound   ≈ 1 gal per 100 sq ft     Tape ≈ 37 ft per 100 sq ft

Sheet counts use the net area plus waste, divided by the sheet size. The finishing figures are trade rules of thumb for a standard three-coat (Level 4) finish. US gypsum manufacturers' literature puts tape at about 370 ft and ready-mixed compound at about 9–11 gallons per 1,000 sq ft.

Screw counts assume framing 16 in on center with screws about 12 in apart on walls (about 32 per 4 × 8 sheet) and a little closer on ceilings.

Worked examples

12 × 12 ft bedroom with 8 ft walls and a ceiling

  1. Walls: 2 × (12 + 12) × 8 = 384 sq ft. Ceiling: 144 sq ft.
  2. Subtract 1 door (21 sq ft) and 2 windows (2 × 15 sq ft): 384 − 51 + 144 = 477 sq ft.
  3. Add 10%: 524.7 sq ft ÷ 32 sq ft per 4 × 8 sheet = 16.4, so 17 sheets.
  4. Finishing: about 513 screws (2 lb), 4.8 gal of compound (two 4.5 gal pails) and 176 ft of tape.

Buy 17 sheets of 4 × 8 drywall.

Basement walls only, 20 × 15 ft, with 4 × 12 ft sheets

  1. Walls: 2 × (20 + 15) × 8 = 560 sq ft − 51 sq ft of openings = 509 sq ft.
  2. +10% = 559.9 sq ft ÷ 48 = 11.7, so 12 sheets.

Buy 12 sheets of 4 × 12 drywall.

Which drywall thickness?

Thickness / typeCommon use
1/2 in regularMost interior walls
1/2 in sag-resistant ceiling boardCeilings with framing up to 24 in on center
5/8 in Type X (fire-rated)Garage walls and ceilings next to living space, and other fire-rated assemblies required by code
Moisture-resistantBathrooms and laundry rooms, but not inside showers
1/4–3/8 in flexibleCurved walls and resurfacing old plaster

Local building codes govern fire-rated and moisture locations. Check with your building department.

Assumptions and limits

  • Rooms are rectangular, with walls of a single height. For cathedral or sloped ceilings, measure each surface and add it as its own room or use the wall area directly.
  • A door is 21 sq ft (3 × 7 ft) and a window 15 sq ft (3 × 5 ft) unless you change it.
  • Waste of 10% covers cut-offs. Rooms with many outside corners, soffits or angles typically need 15%.
  • Finishing supplies are estimates for ready-mixed all-purpose compound and paper tape. Lightweight compound, setting-type compound and mesh tape differ.

Common mistakes to avoid

Subtracting every opening

Small openings often come out of a full sheet anyway, and the cut-out is rarely reusable. Pros frequently skip subtracting windows, so untick the option for a more generous count.

Forgetting corner bead

Every outside corner needs metal or paper-faced corner bead. Measure those corners separately; they are not in the area calculation.

Using standard board in wet areas

Use moisture-resistant board in bathrooms and cement board behind tile in showers. Standard drywall fails when it stays damp.

Frequently asked questions

How many sheets of drywall do I need for a 12 × 12 room?

With 8 ft walls, a ceiling, one door and two windows, about 17 sheets of 4 × 8 drywall including 10% waste. Without the ceiling it is about 12 sheets.

How many screws per sheet of drywall?

About 32 screws for a 4 × 8 sheet on walls with studs 16 in on center, and slightly more on ceilings. A 1 lb box of 1-1/4 in coarse-thread screws holds roughly 250–300 screws.

How much drywall mud (joint compound) do I need?

About 9.4–11 gallons of ready-mixed compound per 1,000 sq ft of drywall for taping plus two finish coats (USG and Fine Homebuilding figures). The calculator uses 10 gallons, which you can change. A 12 × 12 ft room with a ceiling (477 sq ft) needs about 4.8 gallons, or two 4.5 gal pails. A smooth Level 5 finish uses noticeably more.

How do I estimate drywall installation cost?

Add up the materials (sheets, mud, tape, screws) and the labor to hang and finish. Contractors often quote labor per square foot of board. Enter your prices and quote in the calculator and it multiplies them by the quantities it worked out, with materials and labor shown separately. We do not publish average prices, because they vary by region and change often.

Should I hang drywall horizontally or vertically?

On walls, horizontal hanging is common for residential walls 8–9 ft tall. It puts fewer and lower seams across the studs and makes taping easier. Commercial and fire-rated work may require vertical. Sheet count is the same either way.

Is it cheaper to buy 4 × 12 sheets?

Per square foot they cost about the same. Longer sheets mean fewer butt joints to finish, which saves compound and time, but they are heavy and harder to get into a room.

Formulas covered by automated tests · Last reviewed · How we calculate