Backsplash Calculator

Work out the square footage of a kitchen backsplash section by section, then get the tiles or mosaic sheets, boxes, grout and edge trim you need. Waste for the many outlet and cabinet cuts is included.

Units

Example values shown. Replace them with yours.

Backsplash sections

Measure each continuous run of wall between the countertop and the upper cabinets. Behind the range, enter the taller section separately.

Section 1

Usually 18 in from counter to cabinet.

Section 2

Usually 18 in from counter to cabinet.

Areas you will not tile

A window or range hood area. Do not subtract outlets: the cuts around them use that tile anyway.

Your tile
Grout joint width

Rectified porcelain often uses 1/16 in; most other tile 1/8 in or wider.

Used for the grout estimate.

Layout pattern

Extra for cuts, breakage and future repairs.

How it is sold

Printed on the carton label.

Edge trim (optional)

Exposed tile edges, such as the ends of a run or the edge next to a window, need bullnose tile or a metal edge profile.

Metal edge profiles are usually about 8 ft (2.5 m).

Prices (optional)
Tile price is quoted

Before you buy

  • Backsplashes use 15% waste by default. Outlets, window returns and cabinet ends create many small cuts.
  • Most installers run tile all the way to the underside of the upper cabinets and to the outside edge of the countertop.
  • Turn off power before removing outlet covers. You may need box extenders so the outlets sit flush with the new tile.
  • Check whether your mosaic is sold per sheet or per box, then choose the matching option under "How it is sold".

How to use the backsplash calculator

  1. Measure each continuous run of backsplash: the length along the countertop and the height from the counter to the bottom of the upper cabinets (usually 18 in).
  2. Add the taller area behind the range or a window wall as its own section with its real height.
  3. Subtract large areas you will not tile, such as a window or range hood. Do not subtract outlets.
  4. Choose your tile. For mosaics sold on mesh, pick a mosaic size and the tool switches to sheets.
  5. If any tile edges will be exposed, enter that length under Edge trim to get the trim pieces.

The formula

Section area   = length (ft) × height (in) ÷ 12
Backsplash     = Σ section areas − deductions
Tiles          = Backsplash ÷ (tile L + joint) × (tile W + joint)
Boxes / sheets = round up( Backsplash × (1 + waste) ÷ coverage per box or sheet )
Trim pieces    = round up( exposed edge length ÷ piece length )

Backsplash heights are measured in inches, so each section is length in feet × height in inches ÷ 12. A 10 ft run at 18 in high is 15 sq ft.

The default waste is 15%, higher than a floor. Backsplashes are narrow with many short rows, and every outlet, switch, window edge and cabinet end needs a cut.

Worked examples

L-shaped kitchen with a taller section behind the range

  1. Main run: 10 ft × 18 in = 15 sq ft.
  2. Behind the range: 2 ft 6 in × 30 in = 6.25 sq ft.
  3. Total: 21.25 sq ft.
  4. 3 × 6 in subway with 1/8 in joints: 160 tiles, + 15% = 184 tiles.
  5. Boxes of 10 sq ft: 21.25 × 1.15 = 24.4 ÷ 10 = 2.4, so 3 boxes.
  6. Grout: about 3.6 lb, so one 10 lb bag.

Buy 3 boxes of subway tile and one 10 lb bag of grout.

Bar backsplash in 2 × 2 in mosaic sheets

  1. 8 ft × 18 in = 12 sq ft.
  2. Mosaic on 12 × 12 in sheets (about 1 sq ft each), + 15%: 13.8 sq ft.

Buy 14 sheets.

Typical backsplash heights

LocationTypical heightNotes
Between counter and upper cabinets18 inStandard US kitchen
Behind a range with a hood24–30 inMeasure to the bottom of the hood
Full wall, no upper cabinetsTo ceiling or shelfMeasure each wall separately
Bathroom vanity4–6 in, or to mirrorA 4 in splash is usually stone, not tile

Assumptions and limits

  • Each section is treated as a rectangle. For angled ends under a window, measure the rectangle and let the waste allowance cover the triangle.
  • Outlets and switches are not deducted. Their cut-outs are smaller than the tile lost cutting around them.
  • Mosaic sheets are assumed to cover about 1 sq ft each, unless you enter the coverage printed on the product.
  • Grout is a cement-grout estimate with 10% extra. Premixed and epoxy grouts are sold by volume; use their charts.

Common mistakes to avoid

Stopping the tile at the wrong place

Decide where the tile ends before you measure. Common stopping points are the end of the upper cabinets or the outside edge of the countertop. Tile that stops mid-wall needs edge trim.

Forgetting the window returns

If you tile into a window recess, the sides and sill are extra area. Add them as small sections.

Not planning for outlet extenders

Tile and thinset add about 3/8–1/2 in. Outlets may need box extenders so the cover plates sit flush. Code requires the box to be close to the finished surface.

Frequently asked questions

How do I calculate square feet for a backsplash?

Multiply each section's length in inches by its height in inches and divide by 144. Or multiply length in feet by height in inches and divide by 12. Add the sections together and subtract any large window. A 10 ft × 18 in backsplash is 15 sq ft.

How much tile do I need for a 30 sq ft backsplash?

With 15% waste, buy about 34.5 sq ft. That is 4 boxes of 10 sq ft, or 35 mosaic sheets of 1 sq ft.

Do I subtract outlets from backsplash square footage?

No. An outlet opening is only about 0.1 sq ft, and the cuts around it waste more tile than the opening saves.

Should the backsplash go behind the refrigerator?

It is usually not needed, because the fridge hides that wall. Some people tile a few inches past each side of the opening so no edge shows.

How do I finish the exposed edge of a backsplash?

Use a bullnose or pencil trim tile that matches, or a metal edge profile installed with the tile. Measure the total length of exposed edges and enter it to get the number of pieces.

Formulas covered by automated tests · Last reviewed · How we calculate