Paver Calculator

Estimate everything for a paver patio or walkway in one place: the pavers, the gravel base, the bedding sand, polymeric joint sand and the edge restraint. You get a complete material list and an optional cost.

Units

Example values shown. Replace them with yours.

What do you need?
Calculate

Already have the pavers? Choose "base & sand only" for the gravel base, bedding sand and joint sand.

Patio or walkway areas
Area 1
Shape
Pavers

Patio pavers are usually 2-3/8 in (60 mm). Driveway pavers are 3-1/8 in (80 mm).

Joint width
Pattern
Base, sand & edging

Walkways & patios: 4–6 in. Driveways: 8–12 in. Clay soil needs the deeper end.

Dense-grade crushed stone (crusher run, 3/4 in minus).

Screed 1 in of coarse concrete sand. Do not use it to level out low spots in the base.

Leave blank to use the full perimeter. Enter less if one side is against the house.

From the chart on the bag for your joint width and paver thickness. 50 sq ft is the low end of common charts for joints up to 1/4 in.

From your supplier, to see how many pallets to order.

Prices (optional)

Before you buy

  • Excavate to the base depth + sand depth + paver thickness, and allow for a slope away from the house of about 1/4 in per foot.
  • Compact the base in 2 in lifts. Most paver failures come from a thin or poorly compacted base.
  • Pavers are sold by the pallet or by the sq ft. Ask whether partial pallets are available, and whether there is a pallet deposit.
  • Polymeric sand coverage depends heavily on joint width. Check the coverage chart on the bag for your joint width.

How to use the paver calculator

  1. Choose Pavers + base + sand for a full material list, or Paver base & sand only if you already have the pavers.
  2. Add each patio or walkway area as a rectangle, circle or known area.
  3. Choose the paver size and thickness, the joint width and the laying pattern. The pattern sets the waste allowance.
  4. Set the compacted base depth (4 in is typical for patios), the base material weight and the bedding sand depth (1 in).
  5. If part of the edge is against a house or wall, enter the edge restraint length you need.
  6. Optionally add prices for a material cost.

The formula

Pavers         = area ÷ ((paver L + joint) × (paver W + joint)) × (1 + waste %)
Base (tons)    = area × base depth ÷ 12 ÷ 27 × (1 + compaction %) × tons per yd³
Bedding sand   = area × sand depth ÷ 12                 (cu ft)
Joint sand     = round up( area × 1.10 ÷ bag coverage from the chart )
Edge restraint = perimeter ÷ 8 ft pieces

Polymeric sand coverage depends heavily on joint width and paver thickness, so manufacturers print a coverage chart on every bag. Enter the figure for your joints; the calculator adds 10% for sweeping. The default, 50 sq ft per bag, is the low end of published charts for joints up to 1/4 in.

The base gets a 20% compaction allowance by default, because crushed stone settles when you run a plate compactor over it.

Worked examples

16 × 12 ft patio in 4 × 8 in pavers

  1. Area: 192 sq ft. Each paver plus a 1/8 in joint covers 0.233 sq ft, about 4.3 per sq ft.
  2. Pavers: 192 ÷ 0.233 = 825, + 5% = 867.
  3. Base, 4 in: 64 cu ft = 2.37 cu yd, + 20% = 2.84 cu yd × 1.5 = 4.3 tons.
  4. Bedding sand, 1 in: 16 cu ft ≈ 0.8 tons.
  5. Polymeric sand at 50 sq ft per bag: 192 × 1.10 ÷ 50 = 4.2, so 5 bags. Edging: 56 ft, so 7 pieces of 8 ft.

867 pavers, about 4.3 tons of base, 0.8 tons of sand, 5 bags of polymeric sand and 7 edge pieces.

12 ft round fire-pit patio with 6 × 6 in pavers

  1. Area: π × 6² = 113 sq ft.
  2. Pavers: 434, + 15% for curved cuts = 500.
  3. Base: 2.5 tons. Edging: 37.7 ft, so 5 pieces.

Buy 500 pavers and about 2.5 tons of base.

Base depth by use

UseCompacted basePaver thickness
Walkways and patios on firm soil4–6 in2-3/8 in (60 mm)
Patios on clay or poorly drained soil6–8 in2-3/8 in (60 mm)
Residential driveways8–12 in3-1/8 in (80 mm)

Common residential guidance based on industry practice. Paver manufacturers publish their own installation guides; follow them for warranty coverage.

Assumptions and limits

  • Pavers are rectangular and laid on a flat plane. For tumbled or multi-size kits, use the average size or the coverage per pallet from the manufacturer.
  • Joint sand uses the coverage per bag you enter from the manufacturer's chart, plus 10% for sweeping. Charts differ by product, joint width and paver thickness.
  • Bedding sand is coarse concrete sand at about 1.35 tons per cubic yard.
  • Perimeter is calculated for rectangles and circles. For "known area" shapes, enter the edge length yourself.

Common mistakes to avoid

Using sand to fix low spots in the base

Bedding sand should be a uniform 1 in. Thick sand layers settle unevenly and leave dips. Level and compact the gravel base instead.

Skipping edge restraint

Without a restraint the border pavers creep outward, and the joints open up. Use plastic or aluminum edging spiked into the base, or a concrete curb.

Not excavating deep enough

Dig to base + 1 in sand + paver thickness below the finished height, and slope away from the house about 1/4 in per foot.

Frequently asked questions

How many pavers do I need per square foot?

About 4.3 for 4 × 8 in pavers with 1/8 in joints (4.5 with no joints), 3.8 for 6 × 6 in, 2.6 for 6 × 9 in and 1 for 12 × 12 in. Use the calculator for your exact size and joint.

How much base do I need for a 10 × 10 paver patio?

At 4 in compacted with a 20% allowance: 33.3 cu ft = 1.48 cu yd, about 2.2 tons of dense-grade base, plus about 0.42 tons of bedding sand.

How much paver sand do I need?

Bedding sand is a 1 in layer: area × 1 ÷ 12 gives cubic feet. For 100 sq ft that is 8.3 cu ft (0.31 cu yd), about 0.42 tons or 17 bags of 0.5 cu ft. Joint sand is separate: use the coverage chart on the polymeric sand bag. Choose "Paver base & sand only" to calculate just these.

How many bags of polymeric sand do I need?

It depends mainly on joint width and paver thickness. Published charts for 50 lb bags range from about 50–85 sq ft for narrow joints (1/8–1/4 in) down to roughly 15–40 sq ft for wide joints. Enter the figure from your bag's chart above.

Can I use regular sand between pavers?

Yes, but polymeric sand hardens when wetted, which resists weeds, ants and washout. Install it only on a dry day, and sweep the surface completely clean before wetting.

Are pavers sold by the pallet?

Usually, with a pallet covering roughly 80–120 sq ft depending on the paver. Many yards sell partial pallets and charge a refundable pallet deposit.

Formulas covered by automated tests · Last reviewed · How we calculate