General principles
- One set of formulas. All calculations run in US customary units internally. Metric input is converted exactly (1 ft = 0.3048 m) on the way in, and results are converted back for display.
- Round up only at the end. Waste is added to the area or volume first, then the result is divided by the package size and rounded up to whole units.
- Waste is visible and editable. Defaults are common trade allowances. Change them to match your project.
- Tested. The calculation engines have automated unit tests, and every worked example published on a calculator page is tested against the engine.
Tile, grout and flooring
- Tile count uses the tile footprint, which is the tile plus its grout joint, so tile count = area ÷ ((L + joint) × (W + joint)).
- Boxes are based on the coverage printed on the box, including waste. Box coverage is the manufacturer's figure for the nominal tile size.
- Grout volume = area × joint share × tile thickness, where joint share = 1 − (L × W) ÷ ((L + j) × (W + j)). The "from joint size" method converts volume to weight with an editable grout weight per volume (default 100 lb/cu ft ≈ 1.6 kg/L, the value common grout calculators use; not a manufacturer figure). The "from the product chart" method uses the coverage printed by the grout manufacturer and is preferred.
- Shower niches add their four returns (2 × depth × (width + height)); the niche back replaces wall tile. Curbs = length × (2 × height + top width).
Concrete
| Bag | Yield (cu ft) | Source |
|---|---|---|
| 40 lb bag | 0.3 | Quikrete 1101 data sheet |
| 50 lb bag (fast-setting) | 0.375 | Quikrete 1004 fast-setting |
| 60 lb bag | 0.45 | Quikrete 1101 data sheet |
| 80 lb bag | 0.6 | Quikrete 1101-80 listing |
- Ready-mix is rounded up to the next ¼ cubic yard. 1 cu yd = 27 cu ft.
- Thickened edges are a perimeter strip with the corner overlap removed. Rebar is a two-way grid with bars inset from the edges, plus 10% for laps, in 20 ft bars.
- Post holes subtract the post's actual (dressed) cross-section. A 4×4 is 3.5 × 3.5 in.
Masonry
- Blocks are counted by course: courses = height ÷ 8 in (rounded up), and blocks per course = length ÷ 16 in (rounded up to a half block). Nominal sizes include the 3/8 in joint, which gives 1.125 blocks per sq ft.
- Mortar ≈ 33 blocks per 80 lb bag (about 3 bags per 100 blocks), a rule of thumb from US block estimating guides.
Drywall
- Screws: about 1 per sq ft on walls and 1.25 on ceilings; about 300 screws per lb.
- Joint compound: 10 gal per 1,000 sq ft (US gypsum manufacturer literature cites about 9.4 gal; Fine Homebuilding about 11 gal for a three-coat finish).
- Paper tape: about 370 ft per 1,000 sq ft (US gypsum manufacturer estimating guidance).
Gravel, soil, mulch and pavers
Bulk densities are typical loose values in short tons per cubic yard. Real weights vary with the quarry, the gradation and the moisture. Your supplier's scale weight is what you pay for, and every density can be edited.
| Material | Tons per cu yd |
|---|---|
| Crushed stone (#57, 3/4") | 1.4 |
| Pea gravel | 1.4 |
| Crusher run / dense-grade base (3/4" minus) | 1.5 |
| Large base stone (#3, #4, 1.5–2.5") | 1.4 |
| River rock | 1.35 |
| Decomposed granite | 1.35 |
| Sand (concrete / paver sand) | 1.35 |
| Topsoil | 1.1 |
| Fill dirt | 1.1 |
| Wood mulch | 0.3 |
| Concrete (wet) | 2 |
- Compaction allowance is added to volume before converting to tons.
- Polymeric sand bags = area × 1.10 ÷ the coverage per bag from the manufacturer's chart. The default 50 sq ft is the low end of published charts for joints up to 1/4 in (for example Trident/SEK PolySweep: 50–75 sq ft). Change it to match your bag.
- Bagged stone and sand are 0.5 cu ft per bag. Mulch bags use the size you choose (2 cu ft by default).
What our calculators can't know
Your site conditions, local codes, product-specific coverage, installer technique and supplier rounding all affect the final order. Treat every result as a planning estimate, and confirm it with the product label and your supplier. See our disclaimer.
Corrections
If you believe a formula or constant is wrong, please tell us and include your source. We review every report.